<?xml version="1.0" encoding="UTF-8"?><rss xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:atom="http://www.w3.org/2005/Atom" version="2.0"><channel><title><![CDATA[X99老树开花！Windows下成功解锁双3080 20G算力，性能白嫖60%+]]></title><description><![CDATA[<p dir="auto"><img src="https://upload.lcz.me/uploads/f00028a1-87e0-41f7-b621-8bd887fb2766.jpeg" alt="image.jpeg" class="img-markdown  img-fluid" /></p>
<h1>RTX 3080 双卡解锁 · 结果报告（P3）</h1>
<ul>
<li>日期：2026-10-26 01:36–01:37（UEFI 阶段）／01:40（Windows 实测）</li>
<li>结论：<strong>两张 RTX 3080 20GB 均解锁成功</strong>，FP16/BF16 实测 <strong>+58% ~ +63%</strong></li>
<li>承载：U 盘 <code>H:\EFI\BOOT\</code> 三件套（引导器 v3 + 每卡一份 UNLOCK 子程序）</li>
</ul>
<hr />
<h2>1. UEFI 阶段：两趟全部通过</h2>
<table class="table table-bordered table-striped">
<thead>
<tr>
<th></th>
<th>RUN02</th>
<th>RUN03</th>
</tr>
</thead>
<tbody>
<tr>
<td>目标卡</td>
<td><code>83:00.0</code></td>
<td><code>04:00.0</code></td>
</tr>
<tr>
<td>BAR0</td>
<td><code>0xfa000000</code></td>
<td><code>0xc4000000</code></td>
</tr>
<tr>
<td>冷态 SS0 / SS1（写入前）</td>
<td><code>0x41200164</code> / <code>6</code></td>
<td><code>0x04100001</code> / <code>7</code></td>
</tr>
<tr>
<td>写入值</td>
<td><code>0x88888888</code> / <code>0x8</code></td>
<td><code>0x88888888</code> / <code>0x8</code></td>
</tr>
<tr>
<td>FLR 后是否保持</td>
<td><img src="https://lcz.me/assets/plugins/nodebb-plugin-emoji/emoji/android/2705.png?v=3c59dda5525" class="not-responsive emoji emoji-android emoji--white_check_mark" style="height:1.4em;width:auto;vertical-align:middle" title="✅" alt="✅" /> 是</td>
<td><img src="https://lcz.me/assets/plugins/nodebb-plugin-emoji/emoji/android/2705.png?v=3c59dda5525" class="not-responsive emoji emoji-android emoji--white_check_mark" style="height:1.4em;width:auto;vertical-align:middle" title="✅" alt="✅" /> 是</td>
</tr>
<tr>
<td>显示门禁</td>
<td><code>gop=0:3:0.0 target=0:131:0.0 located=1</code></td>
<td><code>gop=0:3:0.0 target=0:4:0.0 located=1</code></td>
</tr>
<tr>
<td>终态</td>
<td><code>status=0 stage=transaction attempted=1 driver_release=1 clean=1</code></td>
<td>同左</td>
</tr>
</tbody>
</table>
<p dir="auto">事务摘要（两卡一致）：</p>
<pre><code>pre-FLR selectors: ss0=0x88888888 expected=0x88888888 ss1=0x8 expected=0x8
post-FLR SEC2 reset released, GSP halted, BME=0 pending=0
  WPR2=1ffffe00:00000000 SS0=88888888 SS1=00000008
transaction result=0 containment=0 started=1 quiesced=1
  fault=0 retained=0 maps=0 FLR=1
FINAL status=0 stage=transaction attempted=1 driver_release=1 clean=1
</code></pre>
<p dir="auto"><code>result=0 fault=0 retained=0</code> → 无故障、无遗留映射、BME 已确保关闭。<br />
全程未触发 <code>Halt</code>/<code>STOP</code>，两卡都在同一通电周期内完成。</p>
<h2>2. Windows 实测（<code>research/bench/gemm_probe.py</code>，224 W 墙）</h2>
<table class="table table-bordered table-striped">
<thead>
<tr>
<th>项目</th>
<th>解锁前基线</th>
<th>04 卡（CUDA 0）</th>
<th>83 卡（CUDA 1）</th>
</tr>
</thead>
<tbody>
<tr>
<td>FP16 8192³</td>
<td>57.88</td>
<td><strong>91.61</strong> (+58.3%)</td>
<td><strong>91.95</strong> (+58.9%)</td>
</tr>
<tr>
<td>BF16 8192³</td>
<td>58.41</td>
<td><strong>93.45</strong> (+60.0%)</td>
<td><strong>95.12</strong> (+62.9%)</td>
</tr>
<tr>
<td>FP16 4096³</td>
<td>53.66</td>
<td>83.20</td>
<td>84.80</td>
</tr>
<tr>
<td>BF16 4096³</td>
<td>54.47</td>
<td>85.41</td>
<td>86.95</td>
</tr>
<tr>
<td>TF32 4096³</td>
<td>27.42</td>
<td>42.54</td>
<td>43.56</td>
</tr>
</tbody>
</table>
<ul>
<li>定点校验（256³ 全 1 矩阵）两卡均 PASS → <strong>数值正确，输出 bit-identical</strong>。</li>
<li>峰值功耗 <code>208~218 / 224 W</code>：功耗墙再次成为上限，不是算力。</li>
<li>采样波动大（min 77 / max 98）是时钟爬坡所致，取中位数。</li>
</ul>
<h2>3. 两个已修 BUG 的验证</h2>
<table class="table table-bordered table-striped">
<thead>
<tr>
<th>BUG</th>
<th>现象</th>
<th>修复</th>
<th>验证</th>
</tr>
</thead>
<tbody>
<tr>
<td>DisplayCheck 用「路径形状」</td>
<td>RUN02 卡在 <code>stage=display</code></td>
<td>改用 <code>PciIo::GetLocation()</code> 比 seg/bus/dev/func</td>
<td>两趟均 <code>located=1</code>，<code>console on target card=0</code></td>
</tr>
<tr>
<td>Launcher 把子程序错误当启动失败</td>
<td>只产出 RUN02、无 RUN03</td>
<td><code>Run()</code> 改为返回 <code>BOOLEAN</code>（能加载即 TRUE）</td>
<td>RUN02 + RUN03 都在</td>
</tr>
</tbody>
</table>
<p dir="auto">附带确认：<strong>SS0/SS1 每次冷启动都会变</strong>（83 卡 <code>0x43200174→0x41200164</code>，04 卡 <code>0x04110005→0x04100001</code>）。<br />
放宽为「只要求 != 0xffffffff」的决定是对的，否则每次冷启动都会假失败。</p>
<h2>4. CUDA 索引（容易踩，已实测）</h2>
<p dir="auto"><code>CUDA_VISIBLE_DEVICES</code> 走 <strong>FASTEST_FIRST</strong>，与 <code>nvidia-smi</code> 的 PCI 顺序不同：</p>
<table class="table table-bordered table-striped">
<thead>
<tr>
<th>值</th>
<th>实际设备</th>
</tr>
</thead>
<tbody>
<tr>
<td><code>0</code></td>
<td>RTX 3080 @ <code>04:00.0</code></td>
</tr>
<tr>
<td><code>1</code></td>
<td>RTX 3080 @ <code>83:00.0</code></td>
</tr>
<tr>
<td><code>2</code></td>
<td>GTX 750 @ <code>03:00.0</code></td>
</tr>
</tbody>
</table>
<ul>
<li><strong>ComfyUI 启动脚本现为 <code>CUDA_VISIBLE_DEVICES=1</code> → 83 卡，本来就没问题，不需要改。</strong></li>
<li><strong>GTX 750 在 torch 2.13.0+cu130 下无 kernel</strong>（sm_50 已被裁掉），任何框架都不能指向索引 <code>2</code>。<br />
它能正常亮机是因为显示走 NVIDIA 驱动，与 CUDA 无关。</li>
</ul>
<h2>5. 必须记住的两件事</h2>
<ol>
<li><strong>解锁只在本次通电周期有效。</strong> 重启 / 关机 / 复位后 SS0/SS1 回到默认，要重跑一次 U 盘仪式<br />
（F11 → UEFI U 盘 → 每趟等 <code>READY</code> 出现后按<strong>一次</strong> U）。这是设计本质，不是故障。</li>
<li><strong>功耗墙 224 W 是用户自设</strong>，未动。双卡同时满载的电源余量尚未测（单卡已顶到 208~218 W）。</li>
</ol>
<h2>6. 产物清单</h2>
<table class="table table-bordered table-striped">
<thead>
<tr>
<th>文件</th>
<th>大小</th>
<th>sha256 前 16 位</th>
</tr>
</thead>
<tbody>
<tr>
<td><code>H:\EFI\BOOT\BOOTX64.EFI</code>（引导器 v3）</td>
<td>5,632 B</td>
<td><code>6804a101aa2fa202</code></td>
</tr>
<tr>
<td><code>H:\EFI\BOOT\UNLOCK_B83.EFI</code></td>
<td>70,656 B</td>
<td><code>370f630acad30a87</code></td>
</tr>
<tr>
<td><code>H:\EFI\BOOT\UNLOCK_B04.EFI</code></td>
<td>70,656 B</td>
<td><code>bbc85223ffb47561</code></td>
</tr>
</tbody>
</table>
<p dir="auto">源码：<code>research/unlock-build/</code>（<code>build_dual.sh</code> / <code>build_launcher.sh</code> / <code>verify_constants.py</code>）。<br />
离线门禁复算：两卡各 21/21 PASS。</p>
]]></description><link>https://lcz.me/topic/2589</link><generator>RSS for Node</generator><lastBuildDate>Sun, 22 Nov 2026 18:06:09 GMT</lastBuildDate><atom:link href="https://lcz.me/topic/2589.rss" rel="self" type="application/rss+xml"/><pubDate>Mon, 26 Oct 2026 02:01:35 GMT</pubDate><ttl>60</ttl><item><title><![CDATA[Reply to X99老树开花！Windows下成功解锁双3080 20G算力，性能白嫖60%+ on Thu, 29 Oct 2026 06:35:50 GMT]]></title><description><![CDATA[<p dir="auto">期待解锁程序更成熟一些，因为没有搞这些基础硬件驱动的能力，只能等各位大神出的成品了。希望能有全系列解锁包的完整解决方案，到时候就直接起飞了。</p>
]]></description><link>https://lcz.me/post/29030</link><guid isPermaLink="true">https://lcz.me/post/29030</guid><dc:creator><![CDATA[ralfzhu]]></dc:creator><pubDate>Thu, 29 Oct 2026 06:35:50 GMT</pubDate></item><item><title><![CDATA[Reply to X99老树开花！Windows下成功解锁双3080 20G算力，性能白嫖60%+ on Tue, 27 Oct 2026 08:28:04 GMT]]></title><description><![CDATA[<p dir="auto">非常好，解锁的测试帖子，参考意义很大。</p>
]]></description><link>https://lcz.me/post/28277</link><guid isPermaLink="true">https://lcz.me/post/28277</guid><dc:creator><![CDATA[terry]]></dc:creator><pubDate>Tue, 27 Oct 2026 08:28:04 GMT</pubDate></item><item><title><![CDATA[Reply to X99老树开花！Windows下成功解锁双3080 20G算力，性能白嫖60%+ on Mon, 26 Oct 2026 02:17:22 GMT]]></title><description><![CDATA[<p dir="auto">为了兼顾性能与稳定，我用小飞机把功耗墙锁在了75%（正好240W），满载核心温度压在60多度。这套配置我插了3张卡，其中一张750专门做亮机输出。因为用的是涡轮卡，为了压制多卡环境下的积热，我在显卡尾部用扎带绑了一个利民静压风扇专门抽热风，目前待机温度只有27°C左右，非常冰凉。电源配的是长城1000W金牌模组，这套系统跑下来极其稳，从来没出现过掉驱动或异常情况</p>
]]></description><link>https://lcz.me/post/27810</link><guid isPermaLink="true">https://lcz.me/post/27810</guid><dc:creator><![CDATA[iliaokun]]></dc:creator><pubDate>Mon, 26 Oct 2026 02:17:22 GMT</pubDate></item><item><title><![CDATA[Reply to X99老树开花！Windows下成功解锁双3080 20G算力，性能白嫖60%+ on Mon, 26 Oct 2026 02:06:06 GMT]]></title><description><![CDATA[<p dir="auto">补充下配置信息：<br />
<img src="https://upload.lcz.me/uploads/e0a13e0b-2644-4a52-9351-9ea5967f794a.jpeg" alt="image.jpeg" class="img-markdown  img-fluid" /></p>
]]></description><link>https://lcz.me/post/27804</link><guid isPermaLink="true">https://lcz.me/post/27804</guid><dc:creator><![CDATA[iliaokun]]></dc:creator><pubDate>Mon, 26 Oct 2026 02:06:06 GMT</pubDate></item></channel></rss>